If this equipment does. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified. This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 3 amp fuse is fitted in this plug. Should the. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug.
A replacement fuse cover can be obtained from your local dealer. If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician. As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in. The wire which is coloured BLUE must be connected to the terminal which is marked with the. How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
Analog signals are transmitted by the shortest circuitry and. As a result, signals are passed to the digital. Mixing is performed with a. These features are housed in a high-rigidity chassis with double-. Equipped with the industry's first "harmonic effect" function that. This new function allows smoother, more natural DJ mixing.
These allow a greater breadth to DJ play by permitting the user to. Also, by combining these with "beat effects," some 50 kinds of effect. The "beat effects" so popular on the DJM are continued here. Some of the effects include delay, echo, reverse delay, pan, trance,. The digital input connectors support each of the sampling rates DJ system with no sound degradation. Only linear PCM is supported. Virtually all the dial and switch information of the DJM can be.
Operating Instructions Power cord Recording output connectors REC. RCA type output connectors for recording. RCA type phono level MM cartridge input connectors. Do not use for inputting line level signals. RCA type line level input connectors. Use to connect a cassette deck or other line level output component. Use to connect ground wires from analog players. This is not a safety grounding terminal. Use to connect a DJ CD player or other line level output component.
LRCK SCLK RXD1 TXD1 V3R3 8. GNDD 6. GNDD 4. GNDD 2. GNDD 1. GNDHP 2. GNDHP 1. Page CF. Page I finish turning it. The default all Lights off. It is possible to return to all Lights off when pressing it 15 times again after it presses it LED on lights most and to repeat from the beginning.
Page 3. The window shown below will open. Click on Next. Leave the check boxes as they are and click on Next. Select International English , then click on Next. You may change the location. If you do not wish to change the location, skip to Step 1. Page You can select the drive in the box enclosed in the lower frame and the folder in the box enclosed in the upper frame in the illustration below: After designating the location for installation, click on OK.
Then the Select Destination Directory window will close. Page When installation is completed, the message shown below 1. Click on Finish. Installation is completed.
Normally, leave the setting as it is and click on Next. Select in the Recommended Next. Speeds: box. Page The program starts.
Designate the file in the User Area: box in File Selection. Click on Options then click to place a check mark in the Request Checksum check box. Now installation and registration of the initial settings have been completed. Page Click on Program Flash. When downloading is finished, click on Disconnect. After confirming that "Disconnected" is displayed in the window, turn off the DJM efx Downloading will start. If you wish to change the device or port settings, select Options then New Settings.
In Writing mode, all the LEDs remain unlit. However, when the DJM efx is turned on or off, it clicks. Page if the port does not need to be changed, skip to "2. Selecting the. When the program starts, the following message will be displayed. Page 2. Designate the port then Right-click on the project name and select Add Files.. The Communications Port window will then close. Downloading the. Click on the Connect icon When the message "Image successfully written to device" to activate connection of the DJM efx with the is displayed, downloading has been finished.
Please exchange the power cord if necessary. When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. Please pay attention to your surroundings and repair safely. To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification. For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper.
Lubricants, Glues, and Replacement parts. Use grease and adhesives that are equal to the specified substance. Make sure the proper amount is applied. Shipping mode and Shipping screws. To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be. Please be sure to follow this method especially if it is specified in this manual. Sampling rate PHONO 2 to Crosstalk LINE RCA pin jacks XLR connectors RCA pin jack Power cord Warranty card Specifications and appearance are subject to change without notice.
Reviews There are no reviews of this manual yet. Related Products. All rights reserved.
0コメント